Setting the Bass Control2-2 Setting the treble Level:
Turn the Rotary encoder to select the desired Treble
You can change the Bass Frequency emphasis toLevel (7~+7).
You can emphasize the treble frequency.
create your own tonal preference.
NOTES
1Press the CENTER f button to select the BASS (bassY If no buttons are pressed within 5 seconds, the Treble control
Center frequency) control mode.setting will be turned off automatically.
Y The settings of the Treble Level will be individually
? BASS ? TREBLE ? normal modememorized for each source (FM, AM, XM, CD, etc.) until the
setting is changed. Once you set Treble frequency for one of
sources (FM, AM, XM, CD, etc.), this setting becomes
2-1Setting the bass Center frequency:effective for all those sources. Depending on the connected
Press the g DN or f UP button to select thedevices, some functions and display indications do not work.
desired bass center frequency.Y This function is inoperable when DEFEAT is ON.
Adjusting the built-in Crossover? 60Hz ? 70Hz ? 80Hz ? 90Hz ?
? 180Hz ? 150Hz ? 130Hz ? 100Hz?
Emphasizes the displayed Bass frequency ranges.
The High and Low Pass Filters on this unit can be
adjusted to suit your personal taste.
2-2Setting the bass Band Width (Q-Factor):
Press the BAND button to select the desired bass
1Press and hold the X-OVER button for at least 2
Band Width.
seconds.
? B. Width1 ? B. Width2 ? B. Width3 ? B. Width4
(Wide) ?.....................................? (Narrow)? HPF <Press momentarily>? LPF <Press momentarily>
<Press for at least 2 seconds> normal mode ?
Changes the bass boost band width to wide or narrow.When the subwoofer output of this unit is turned
A wide setting will boost a wide range of frequencies
above and below the center frequency. A narrowerOFF, LPF and phase are deactivated.
setting will boost only frequencies near the center
frequency.2Press the g DN or f UP button to select the
desired setting.
2-3Setting the bass Level:1. HPF (Setting the High Pass Filter):
Turn the Rotary encoder to select the desired bass
FLAT (OFF) ? 80Hz ? 120Hz ?160Hz
Level (7~+7).
You can emphasize or weaken the bass frequency.Outputs all frequencies higher than that selected
according to your preference.
NOTES
YIf no buttons are pressed within 5 seconds, the Bass control2. LPF(Setting the Low Pass Filter):
setting will be turned off automatically.
FLAT (OFF) ? 80Hz ? 120Hz ?160Hz
YThe settings of the Bass Level will be individually memorized
for each source (FM, AM, XM, CD, etc.) until the setting isOutputs all frequencies lower than that selected
changed. Once you set Bass frequency and Bass Band Width foraccording to your preference.
one of sources (FM, AM, XM, CD, etc.), this setting becomes
effective for all those sources. Depending on the connected(Only available when using the subwoofer output from
devices, some functions and display indications do not work.this unit.)
Y This function is inoperable when DEFEAT is ON.NOTES
" If no buttons are pressed within 5 seconds, the setup menu
Setting the Treble Controlreturns to the normal audio display.
" These functions are inoperative when an external, Ai-NET
processor is connected.
You can change the Treble Frequency emphasis to" If HPF, LPF, Bass Control and Treble Control are all set to
create your own tonal preference.ON, depending on the Bass Control and Treble Control
settings, you may not be able to reinforce the sound effect.
1Press the CENTER f button to select the TREBLE" Except when the HPF and LPF is turned OFF, the subwoofer
is in monaural mode.
(treble Center frequency) control mode.
" When the subwoofer is set to OFF, LPF mode and change of
? BASS ? TREBLE ? normal modephase does not work.
2-1Setting the treble Center frequency:
Press g DN or f UP button to select the desired
treble Center frequency.
? 10.0kHz ? 12.5kHz ? 15.0kHz ? 17.5kHz ?
Emphasizes the displayed Treble frequency ranges.
7-EN |